Merge pull request #3055 from CumulusNetworks/create-pull-request/patch

Changes by create-pull-request action

Author: mergify[bot]

content/cumulus-linux-512/Whats-New/rn.md

@@ -54,8 +54,8 @@ pdfhidden: True
 | <a name="4521203"></a> [4521203](#4521203) <a name="4521203"></a> <br /> | The SATA driver on the NVIDIA SN2410 switch sometimes exhibits failures similar to the following:<br><pre>2025-06-20T20:03:38.785966+09:00 S1-RF10B kernel: <br>&#91;49878794.456350&#93; ata1.00: failed command: WRITE FPDMA QUEUED<br>2025-06-20T20:03:38.785968+09:00 S1-RF10B kernel: &#91;49878794.461984&#93; ata1.00: cmd<br>61/08:08:50:2b:c4/00:00:01:00:00/40 tag 1 ncq dma 4096 out<br>2025-06-20T20:03:38.785970+09:00 S1-RF10B kernel: &#91;49878794.461984&#93; res 40/00:0c:50:2b:c4/00:00:01:00:00/40 Emask 0×10 (ATA bus error)</pre><br>To work around this issue, power cycle the switch. | 5.5.1-5.13.1 | 5.14.0-5.15.1|
 | <a name="4509255"></a> [4509255](#4509255) <a name="4509255"></a> <br /> | In PTP two-step, the hardware incorrectly modifies the SYNC message correction field. | 5.12.0-5.15.1 | |
 | <a name="4508830"></a> [4508830](#4508830) <a name="4508830"></a> <br /> | Cumulus Linux allows you to add bond ports of mismatched speeds (such as 10G and 25G) to the same LACP bond without error and the bond reports UP.  | 5.11.2-5.15.1 | |
-| <a name="4499025"></a> [4499025](#4499025) <a name="4499025"></a> <br /> | You see a high volume of NAT and NFCT errors flooding <code>switchd</code> logs. This issue has no functional impact. | 5.11.2-5.15.1 | |
 | <a name="4495231"></a> [4495231](#4495231) <a name="4495231"></a> <br /> | If the hardware clock date is later than 2038-01-19 03:14:07 UTC, the image might fail to install due to a grub-install failure on the EFI filesystem, which is a VFAT filesystem.  As a result, you see the grub prompt immediately after reboot.  To work around this issue, reboot from the grub prompt to go into ONIE.  From ONIE, use the date command to set a date before 2038-01-19, then run the <code>hwclock --systohc</code> command to add it to the hardware clock.  You can then use <code>onie-nos-install</code> to install the image. | 5.9.0-5.15.1 | |
+| <a name="4486668"></a> [4486668](#4486668) <a name="4486668"></a> <br /> | You see a high volume of NAT and NFCT errors flooding <code>switchd</code> logs. This issue has no functional impact. | 5.11.2-5.13.1 | 5.14.0-5.15.1|
 | <a name="4486200"></a> [4486200](#4486200) <a name="4486200"></a> <br /> | If you enable dynamic NAT and try to install two identical dynamic NAT rules, <code>switchd</code> might crash. | 5.11.2-5.13.1 | 5.14.0-5.15.1|
 | <a name="4475111"></a> [4475111](#4475111) <a name="4475111"></a> <br /> | When you try to convert a layer 3 port that is part of ECMP to a bond member,  you might see a failure in the <code>switchd</code> logs. This issue does not have any functional impact. | 5.11.2-5.15.1 | 5.9.4|
 | <a name="4472414"></a> [4472414](#4472414) <a name="4472414"></a> <br /> | After you modify the IP address of an SVI, DHCP relay uses an old cached IP address instead of the changed IP address. This occurs because DHCP relay monitors the link state change not IP address change. | 5.11.0-5.14.0 | 5.15.0-5.15.1|
@@ -242,8 +242,8 @@ pdfhidden: True
 | <a name="4521203"></a> [4521203](#4521203) <a name="4521203"></a> <br /> | The SATA driver on the NVIDIA SN2410 switch sometimes exhibits failures similar to the following:<br><pre>2025-06-20T20:03:38.785966+09:00 S1-RF10B kernel: <br>&#91;49878794.456350&#93; ata1.00: failed command: WRITE FPDMA QUEUED<br>2025-06-20T20:03:38.785968+09:00 S1-RF10B kernel: &#91;49878794.461984&#93; ata1.00: cmd<br>61/08:08:50:2b:c4/00:00:01:00:00/40 tag 1 ncq dma 4096 out<br>2025-06-20T20:03:38.785970+09:00 S1-RF10B kernel: &#91;49878794.461984&#93; res 40/00:0c:50:2b:c4/00:00:01:00:00/40 Emask 0×10 (ATA bus error)</pre><br>To work around this issue, power cycle the switch. | 5.5.1-5.13.1 | 5.14.0-5.15.1|
 | <a name="4509255"></a> [4509255](#4509255) <a name="4509255"></a> <br /> | In PTP two-step, the hardware incorrectly modifies the SYNC message correction field. | 5.12.0-5.15.1 | |
 | <a name="4508830"></a> [4508830](#4508830) <a name="4508830"></a> <br /> | Cumulus Linux allows you to add bond ports of mismatched speeds (such as 10G and 25G) to the same LACP bond without error and the bond reports UP.  | 5.11.2-5.15.1 | |
-| <a name="4499025"></a> [4499025](#4499025) <a name="4499025"></a> <br /> | You see a high volume of NAT and NFCT errors flooding <code>switchd</code> logs. This issue has no functional impact. | 5.11.2-5.15.1 | |
 | <a name="4495231"></a> [4495231](#4495231) <a name="4495231"></a> <br /> | If the hardware clock date is later than 2038-01-19 03:14:07 UTC, the image might fail to install due to a grub-install failure on the EFI filesystem, which is a VFAT filesystem.  As a result, you see the grub prompt immediately after reboot.  To work around this issue, reboot from the grub prompt to go into ONIE.  From ONIE, use the date command to set a date before 2038-01-19, then run the <code>hwclock --systohc</code> command to add it to the hardware clock.  You can then use <code>onie-nos-install</code> to install the image. | 5.9.0-5.15.1 | |
+| <a name="4486668"></a> [4486668](#4486668) <a name="4486668"></a> <br /> | You see a high volume of NAT and NFCT errors flooding <code>switchd</code> logs. This issue has no functional impact. | 5.11.2-5.13.1 | 5.14.0-5.15.1|
 | <a name="4486200"></a> [4486200](#4486200) <a name="4486200"></a> <br /> | If you enable dynamic NAT and try to install two identical dynamic NAT rules, <code>switchd</code> might crash. | 5.11.2-5.13.1 | 5.14.0-5.15.1|
 | <a name="4475111"></a> [4475111](#4475111) <a name="4475111"></a> <br /> | When you try to convert a layer 3 port that is part of ECMP to a bond member,  you might see a failure in the <code>switchd</code> logs. This issue does not have any functional impact. | 5.11.2-5.15.1 | 5.9.4|
 | <a name="4472414"></a> [4472414](#4472414) <a name="4472414"></a> <br /> | After you modify the IP address of an SVI, DHCP relay uses an old cached IP address instead of the changed IP address. This occurs because DHCP relay monitors the link state change not IP address change. | 5.11.0-5.14.0 | 5.15.0-5.15.1|

content/cumulus-linux-512/rn.xml

@@ -264,18 +264,18 @@ To work around this issue, power cycle the switch.</td>
 <td></td>
 </tr>
 <tr>
-<td>4499025</td>
-<td>You see a high volume of NAT and NFCT errors flooding {{switchd}} logs. This issue has no functional impact.</td>
-<td>5.11.2-5.15.1</td>
-<td></td>
-</tr>
-<tr>
 <td>4495231</td>
 <td>If the hardware clock date is later than 2038-01-19 03:14:07 UTC, the image might fail to install due to a grub-install failure on the EFI filesystem, which is a VFAT filesystem.  As a result, you see the grub prompt immediately after reboot.  To work around this issue, reboot from the grub prompt to go into ONIE.  From ONIE, use the date command to set a date before 2038-01-19, then run the {{hwclock --systohc}} command to add it to the hardware clock.  You can then use {{onie-nos-install}} to install the image.</td>
 <td>5.9.0-5.15.1</td>
 <td></td>
 </tr>
 <tr>
+<td>4486668</td>
+<td>You see a high volume of NAT and NFCT errors flooding {{switchd}} logs. This issue has no functional impact.</td>
+<td>5.11.2-5.13.1</td>
+<td>5.14.0-5.15.1</td>
+</tr>
+<tr>
 <td>4486200</td>
 <td>If you enable dynamic NAT and try to install two identical dynamic NAT rules, {{switchd}} might crash.</td>
 <td>5.11.2-5.13.1</td>
@@ -1424,18 +1424,18 @@ To work around this issue, power cycle the switch.</td>
 <td></td>
 </tr>
 <tr>
-<td>4499025</td>
-<td>You see a high volume of NAT and NFCT errors flooding {{switchd}} logs. This issue has no functional impact.</td>
-<td>5.11.2-5.15.1</td>
-<td></td>
-</tr>
-<tr>
 <td>4495231</td>
 <td>If the hardware clock date is later than 2038-01-19 03:14:07 UTC, the image might fail to install due to a grub-install failure on the EFI filesystem, which is a VFAT filesystem.  As a result, you see the grub prompt immediately after reboot.  To work around this issue, reboot from the grub prompt to go into ONIE.  From ONIE, use the date command to set a date before 2038-01-19, then run the {{hwclock --systohc}} command to add it to the hardware clock.  You can then use {{onie-nos-install}} to install the image.</td>
 <td>5.9.0-5.15.1</td>
 <td></td>
 </tr>
 <tr>
+<td>4486668</td>
+<td>You see a high volume of NAT and NFCT errors flooding {{switchd}} logs. This issue has no functional impact.</td>
+<td>5.11.2-5.13.1</td>
+<td>5.14.0-5.15.1</td>
+</tr>
+<tr>
 <td>4486200</td>
 <td>If you enable dynamic NAT and try to install two identical dynamic NAT rules, {{switchd}} might crash.</td>
 <td>5.11.2-5.13.1</td>